How to Install a Vinyl Fence
A fence made of vinyl is a beautiful and low-maintenance means to delineate property lines and keep children and pets safe and secure. However, it is essential to take note of every aspect of putting up a fence made of vinyl.
The first step is to stake out the fence you intend to construct and calculate how many posts you'll need. Fence posts should be placed 6-8 feet apart.
Dig Postholes
Dig postholes in your fence line using a powered auger or digger (check the local codes). The holes should be around 10 inches in diameter . They should be deep enough to hold around 1/3 of the length of the pole plus 6 inches of gravel backfill. Gate posts and main supports should usually be six inches higher than other posts to improve strength.
After digging the posts after digging them, pour six inches of gravel into them. Then, fill them with quick-setting concrete. Follow the mixing and setting guidelines on the concrete bag. Tap the hollow post into the concrete, and then ensure that the post is level and plumb before moving on to the next.
If your fence is located on top of a water source Consider a drainage plan to prevent the water from entering the post holes. To prevent erosion from water, you can also add gravel between the fence and the ground.
Call your local utility diggers hotline prior to you start digging. vinyl fencing installers will mark underground lines. This will ensure that you do not run into any unexpected circumstances, like a leaking water or sewer line, when you are installing your fence.
Once you have marked the holes, dig each to an average depth of 2.5 to 3 feet. To ensure that the rails of your post can fit inside the holes, the bottom of the hole should be wider then the top of the post.
Reduce the length of your posts
You must ensure that the posts are the same length if you wish to put up vinyl fencing. This will allow the fence to bend but not break. This helps ensure that the fence can stand up to minor impacts and high winds.
To make sure you have the same length of post you can use a level measure each post and mark them on strings. You can mark the strings at the end of posts, or use them to line up each posthole.
Once you've marked the posts, you need to dig holes to the required depth to construct the fence. They should be large enough to hold 3 feet of post plus 6 inches of gravel, which serves as a foundation for the post that will allow water to drain away from it.
Then, you can insert the bottom rail into each post and secure it with an self-drilling screw. This will stop the top rail from slipping off the post, and will allow for in-and-out movement.
After fencing installation cost put the bottom rail in then slide your pickets in and U-channels as needed until you've completed the entire section. After that, you can slide in your top and middle rails.
If you're planning to install a privacy vinyl fence, you can insert the u-channel before you nail the top rail into the post. This will stop your fence from sliding in the wind and will helps to keep out insects and other debris.
Install Posts
When you put up an outdoor fence made of vinyl it is important to adhere to the manufacturer's guidelines for installing the posts. This includes digging holes that are sufficient in depth to hold at least 1/3 of the post's length and six inches deeper if you're using a gravel base.
If you're installing a fence made of vinyl on an inclined slope, it's important to make sure that the posts are level. This is because a high-pitched post can cause the entire fence to be sagging and make it difficult to secure the fence properly.
Before digging the hole Before digging, secure a string at each corner or end of your posts to ensure that they are straight. This will help you locate the exact position of the post.
Ideally, the posts should be about three-quarters longer than their length to give them more strength and stability. Digging them with a post-hole digger is a quick and simple method of doing this however, you can also dig them by hand.
After the posts are set placed then pour concrete over them. The cement should be around 1 foot deep, and evenly spread. This will ensure that the posts are more durable and make them more able to withstand high winds.
Once all posts are set after which you can connect rails to them. The rails snap into slots on the top and bottom of the posts. Once the rails are secured, you can slide your vinyl fencing panels into position.
Attach Posts to Rails
Vinyl fences are constructed using posts, and must be sturdy enough to support the weight of the fence. Posts could tip or move if the ground is unstable. This could cause damage to your fence. Concrete in the base is the best method to ensure strength for your posts.
The process of attaching a rail to a rail isn't easy however it's not difficult. To ensure that your post stays straight and level it is possible to use a "post brace". They are usually constructed of boards measuring 2 feet by 4 feet that attach to the post with nails or an hammer with claws.
Once the post is secure Set the rails on the top of it. If you are installing split rails move the rail that is on the bottom down until it clears one of the adjacent posts. Continue adding rails until all posts have been installed and the fence is completed.
For pickets that are spaced, consult your local code enforcement office for specific spacing. If your fence is situated in a sloped area you might need to cut the pickets into an angled pattern. Although it's not required to do so, it can disguise the boards that have uneven ends.
It is essential to select the appropriate style of fence for your landscape and home. The fence should complement the overall design of your home and offer privacy, security and curb appeal. fencing installation cost can aid in reducing the cost of maintenance and replacement of your fence.
Attach rails to posts
Vinyl fences are simple to set up and come in a variety of styles. These include privacy fences as well as split rail and picket fences. These fences are sturdy and require minimal maintenance, which makes them a popular choice for wood fences.
Before vinyl fencing installers start digging holes for the posts the distance between each of the posts to make sure that the fence is set in a straight line. Then use a string to mark and set all of the posts.
When the posts are ready to be erected, you must dig holes for each post leaving 5 to 6 inches above the ground. If you live on a slope, concrete can be added to the bottom of each post.
After all the posts are in place Once the posts are in place, you can connect the fence rails to them. The fence rails made of vinyl are available in lengths of 16 and 8 feet so you can pick the most appropriate size for your home.
If the fence has corners, you'll need to cut the rails in order to fit around the corner. You can use the top of one rail to slide it over the corner post, and the opposite end of the rail to slip it into the next post.
After you have attached the rails, place the fence pickets in the rails. This will create a clean professional look for your fence. It will also give you the opportunity to visually grade your fence to ensure it appears consistent from some distance.
Attach posts to other posts
Vinyl fences are an excellent option for homeowners looking to improve their property's curb appeal, privacy, and protect their property from weather-related damage. They are sturdy and require very little maintenance.
There are many kinds of vinyl fences available that include picket, solid privacy and picket. Each style of fence is available in various sizes and colors and some are sold with a lifetime warranty.
Be aware of the manufacturing process used by the vinyl fence manufacturer when selecting a fence for your home. Vinyl fencing is made in two main ways: monoextrusion or co-extrusion.
The first method injects polyvinyl chloride (PVC) with UV inhibitors to prevent chalking and fading. To create a capstock as well as a substrate the second method employs a double layer of PVC.
Vinyl fences are also infused with impact modifiers, stabilizers and other materials that make them strong and flexible. They are impervious to rot and decay, and some fences have the promise of a lifetime.
If you're not sure about the type of vinyl fence to buy contact your local dealer for suggestions. They can help you choose the ideal fence for your needs and help you make the right choice.
If you've decided to purchase a fence made of vinyl that will fit your home, it is time to begin the installation. This step isn't simple, so be sure you follow the steps.